BRAND: MERIDIAN SERVICE MANUAL LAUNDRY PRODUCTS Combo Washer Dryer MODELS MD3720CEE (WHITE / PLATINUM) - VENTLESS
10 regulator and the wire M1 on the motor connector, if there is no continuity, the wash timer is bad, check the continuity between terminals 3 &am
11 3) Clothes hot and damp at the end of dry cycle a) Blocked filter / Coin Trap: Remove, clean, and replace filter. b) *No cold water supply: Col
12 Replacement Procedure, Wiring & Testing of Parts 1) Power Switch (52799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top p
13 2) Door Switch / Door Lock (00750) Replacement Procedure: ▪ Unplug the unit. ▪ Open the door remove the clamp to the door gasket in the fr
14 3) Pressure Switch (50774) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix t
15 4) Cold water valve (10820) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix t
16 5) Hot water valve (00821) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Unfix
17 6) Wash Timer (50819) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out the s
18 7) Dry Timer (50728) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out the so
19 8) Half Load Switch (51799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull ou
2 # TABLE OF CONTENTS # • Warranty Information………………………….……….………………….. 3 • Safe Servicing Practices……………………………………………………… 4 • Inst
20 9) Half Heat Switch (50799) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ Pull out
21 10) Fusible Link / Wire with fuse (00807) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide bac
22 11) Thermostat (00808) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The fusible l
23 12) Fan Motor (50732) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The fan motor
24 13) Blower / Fan / Impeller Assembly (51733) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide
25 14) Heating Element (00745) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The he
26 15) Speed Regulator (00791) Replacement Procedure: ▪ Unplug the unit. ▪ Remove the top panel (Two screws behind and slide back) ▪ The speed
27 16) Drain Pump (00776) Replacement Procedure: ▪ Unplug the unit. ▪ Make sure that there is no water in the unit. ▪ Carefully pull out the k
28 17) Main Motor (50751) Replacement Procedure: ▪ Unplug the unit. ▪ Make sure that there is no water in the unit. ▪ Remove the back panel (3
29 Quick Check After replacing any part in the unit you can do a quick check to make sure that the unit is working normal by following the procedu
3 WARRANTY INFORMATION FULL ONE-YEAR WARRANTY Meridian Appliances undertakes to the consumer-owner to repair or, at Meridian Appliances’ option, to r
30 COMPANY INFORMATION APPLIANCE DESK BRAND: MERIDIAN CONTACT NUMBERS SERVICE, PARTS, ACCESSORIES & DETERGENT ORDERING: (800
4 SAFE SERVICING PRACTICES To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be obser
5 INSTALLATION (MD 3720 CEE ) Inlet Hoses The inlet hoses must be fitted with the special rubber washers. These rubber washers ensure a water tight
6 IMPORTANT PRESERVICE INSTRUCTIONS ► It is advisable for anyone to go through the following points before one actually works
7 DIAGNOSIS AND TECHNICAL TROUBLESHOOTING ◊ INSTALLATION ◊ 1) Machine vibrating or vibrating noise a) Shipping bolts not removed: There are 3 ship
8 is present, the machine should fill. If not, the valve is defective. 2) Unit fills, won’t agitate / tumble a) Belt: Check belt, adjust tension
9 b) Unstable floor: Remove carpeting, move to another location, or install underlayment. c) Unit not leveled properly: Adjust leveling legs, tight
Comments to this Manuals